Does Starlink Work During Power Outages?
Yes, Starlink can keep working during a local power outage if backup power keeps its dish, power supply, and router running. Without that backup, the equipment switches off with your electricity. A working battery also cannot guarantee internet access if severe weather, damaged equipment, or a Starlink network problem interrupts the connection.
A power cut at home does not switch off the whole network
Starlink’s satellites and wider network can keep operating when your local electricity fails. Your own equipment still needs a power source.
- Local outage, no backupEquipment stops
The dish and router lose power, so the satellite connection is unavailable.
- Local outage, kit poweredCan stay online
Service can continue while the backup lasts and the wider connection is available.
- Weather or network failurePower is not enough
A battery keeps equipment running; it cannot repair a damaged link or restore a failed service.
Starlink reports that customers using backup power stayed connected during the April 2025 outage in Spain and Portugal, with traffic rerouted through unaffected ground stations. The available route still matters, so a battery-backed kit cannot guarantee the same result in every outage.
Keep the whole connection powered
A common weak point is a router, Ethernet switch, or mesh node left on an ordinary wall outlet. The dish can have power while the device you use still has no working path to it.
Backup supply
Provides the power when the wall supply fails.
Kit power input
Use the normal, compatible input for your model.
Dish and router
Both must remain powered. Mini has Wi-Fi built into the terminal.
Include any separate router, switch, or mesh node needed to reach your chosen device, and keep that phone or laptop charged. If Starlink is a second internet connection, the router that switches between providers needs backup power too.
Check which Starlink kit you have
The hardware makes a substantial difference to battery runtime. Starlink publishes these average power figures; they are not maximum-load ratings.
- Standard 4 / 4 X
- 75–100 WStarlink’s support figure includes the kit’s router, power supply, and cables.
- Mini
- 20–40 WAverage in Starlink’s power-support guidance. Its Wi-Fi is integrated.
- V5
- 35–50 WPublished in Starlink’s V4/V5 comparison. Use measured total draw, including your router, when sizing backup.
Older and Performance kits can have different requirements. Match the exact model before choosing equipment. Our Starlink V5 hardware guide covers the newer residential dish in more detail.
For an AC-powered setup, a plug-in power meter can show the draw at the wall under normal use. Count any additional devices separately, without adding the included Starlink router twice.
How long will a battery run Starlink?
Start with stored energy in watt-hours (Wh), then divide the usable energy by the total load in watts (W). Allow for conversion losses and the battery’s usable capacity.
Battery Wh × usable fraction ÷ total watts
One 500 Wh battery, two example loads
The 80% allowance is an assumption for these examples, not a specification for a particular battery. Inverter overhead, temperature, battery condition, reserve settings, and changing power draw can all alter the result.
Compare battery sizes at the same load
These estimates use the same 80% usable-energy assumption and steady total loads.
| Rated capacity | At 40 W total | At 100 W total |
|---|---|---|
| 250 Wh | 5 hours | 2 hours |
| 500 Wh | 10 hours | 4 hours |
| 1,000 Wh | 20 hours | 8 hours |
A laptop can change the calculation
At 100 W, the 500 Wh example gives four hours. Add a laptop drawing an illustrative 50 W from the same battery and the total becomes 150 W: about two hours and 40 minutes. Running the laptop on its own battery preserves more energy for the connection.
Choose a setup that comfortably exceeds the time you need. An estimate of exactly four hours leaves little room for an older battery, extra equipment, or a longer outage.
Which kind of backup makes sense?
A 1,000 VA UPS is not a 1,000 Wh battery. Use its actual runtime chart and both its watt and VA limits. Likewise, a portable power station with pass-through charging is not automatically a UPS; verify the manufacturer’s switchover specification.
For a fuel-powered portable generator, follow its operating instructions and keep it outdoors. The CDC specifies at least 20 feet, about 6 meters, from doors, windows, and vents.
Mini needs the right power bank, not just a large one
Starlink specifies a 100 W USB-C Power Delivery source at 20 V / 5 A when powering Mini through its USB-C-to-barrel cable.
The required supply capability is different from Mini’s average consumption. A 100 W port does not mean Mini draws 100 W continuously.
Check the capability of the individual port and compatible cable, including what happens if another device shares the bank. Battery capacity alone does not establish compatibility. For Standard kits, use the model’s approved power arrangement rather than assuming Mini accessories will work.
Do one deliberate test before you need it
The most useful test is whether the whole setup survives losing mains power while you are actually using the connection.
Charge and connect
Fully charge the backup. Connect every device needed for your chosen internet path to the appropriate backed-up outlets.
Simulate the outage
Follow the backup maker’s instructions. For a normal plug-in setup, test loss of its wall input while the Starlink kit remains connected to the backup.
Use a real service
Open a fresh webpage or keep a call running. A saved Wi-Fi connection or cached page alone does not demonstrate internet access.
Check the handover and load
Note any reboot, overload warning, and the power draw. Confirm that the phone or laptop still works from the place you plan to use it.
I’d make a reliable handover the first priority, then check runtime. Several hours of stored energy are less useful for a live call if the equipment reboots every time the power flickers.
What if the kit has power but there is no internet?
No Wi-Fi network
Check router power and any separate mesh equipment. Confirm that the backup outlet is enabled and has not overloaded.
Wi-Fi works, websites do not
Check the Starlink app for alerts and inspect accessible connections. The router being on does not establish that the dish has power or a usable satellite link.
It drops when the wall power fails
The transfer may interrupt power, or the supply may be unable to carry the load. Compare the behavior with the backup manufacturer’s specifications.
Heavy rain, snow, or hail can interrupt the radio link. Storms can affect ground stations too. A moved dish, damaged cable, or new obstruction can leave the equipment powered but offline; our guide to trees and Starlink obstructions explains the sky-view requirement.
Snow Melt can add to consumption, particularly in Pre-heat mode. Starlink recommends Automatic, which heats when needed. Allow for winter conditions in your backup plan.
If internet calling is part of that plan, remember that the calling device and any phone equipment also need power. The digital landline power-cut guide covers that separate issue for UK households.
Starlink power-outage questions
Does an ordinary Starlink kit have a built-in backup battery?
No. These kits rely on external power. A compatible UPS, power station, or other backup is needed to keep them running when their normal supply fails.
Can solar panels keep Starlink online?
A suitable solar-and-battery system can supply it. Size the battery for the hours without adequate sunlight and check charging limits as well as output power. Panel wattage alone does not guarantee continuous service through a cloudy day or overnight.
Is this the same as Starlink service directly to a phone?
No. This guide concerns a powered Starlink broadband kit. Satellite-to-phone services have separate devices, carrier arrangements, coverage, and service terms. Our Starlink Mobile explainer covers that distinction.
Back up the connection you will actually use
Start with the exact kit, include the router and any essential extra equipment, then test the handover. Size the battery around that complete load with enough margin for the outage you want to cover.

